Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
The author is making a few great annotation regarding Tools You Need to Install a New Bathtub as a whole in this great article beneath.
Installing a bath tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old tub is conveniently available, the project can relocate immediately; if you need to open a wall to get rid of the old tub as well as position the new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub and set in the new one. Make certain you have actually qualified on your own for the work and also are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is better to consider utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your shower room if you have already purchased a brand-new bathtub and don't require to alter the setup of your previous water pipes.
Your devices as well as product list must make up the following:
Planning for the Setup
First of all, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing faucets can be rather bothersome because of the restricted access that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the called for setting. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four little points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water as well as examine all joints as well as new pipework for leakages as well as tighten them if required. Fill the bath tub and also examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bath tub must wait until the bathtub has actually been made use of at least once as this will settle it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washers remain in location between the tap as well as the sink. Safeguard the faucet in position with the producer given backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The previous type ought to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with moisture as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealant can fracture fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly offered on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very excited about Installing A Bathtub and I hope you liked the entire blog entry. You should take the opportunity to share this blog if you enjoyed it. Thank you for your time. Visit again soon.
Dial, stress less! Report this page